PDA

View Full Version : Chris



mazdarati
03-16-2009, 11:51 PM
thats me hunched over by the tire


Thought i would finally make a drivers page on here. As some of you know im the one with the silver RX7 that used to run a few months ago, ive been with out her for too long now due to the rear rotor losing compression. I have probably met just about everyone on here in one way or another, probably because i have been under your busted ass 240 fixing shit ;D

all kidding aside though, im almost always the one who is dirty/greasy and underneath a 240 over at ryans house. Right now i am in a "rental" thanks to clarkbar "aka" chaaaaaarles. I work at nissan with him and travis now, right across from the mazda dealership (ironic huh?) anyways...back to the important stuff

the cars:
91 RX7 GTU

Mods:
Terribly loud, almost straight exhaust
Mistubishi Starion rims 16x7 front 16x8 rear if i remember correctly, both 0 offset
space invader sticker on the center tail light
wideband O2 sensor to tell me how terribly rich my car is running at all times
Tein drop springs on stock struts



hopefully i will have this thing running again soon

95 MX6
This has been a project of mine for way to long, it was previously turbo'd but the owner had the intake manifold taken off and most of the turbo stuff taken off when i bought it and it has not changed very much since i first got it other than putting most of the parts back on the car. Since i ran into money problems and i just want to get the car running again it will not be turbo'd any time soon, but it should still be a fun daily once its done

Engine: 2.5L V6 w/ KL-ZE intake manifold
SS Autochrome turbo headers
3in exhaust with magnaflow muffler
MSD 6AL ignition box w/external coil
Modified disty to accomodate the external coil
Megasquirt v2.2 with NA base map
stronger gears in the tranny (supposedly)
Battery relocated to the trunk

Interior:basically stripped out at the moment
custom B-piller bar for harness


Exterior: JDM headlights with HID's (7k i think)
JDM taillights
Racing Heart rims off an MSP

Clarkbar
03-17-2009, 02:33 AM
hey chris lets get a motor already for the rx!!! i miss that annoying gas guzzler hahaha

killakingquan
03-17-2009, 09:37 AM
put a sr in it

Clarkbar
03-17-2009, 07:54 PM
no more sr motors there is enough already!!!! if any LS1!!

guffman
03-19-2009, 08:07 PM
too many pics of that fwd guffness, buy another stupid dorito engine and put it in for God's sake, someone has to have a running FC out of everyone.

feare30s
03-31-2009, 05:45 PM
SICK FC i want one

killakingquan
04-01-2009, 08:15 PM
hey um lets atleast throw some shit in the fc and get it goin

mazdarati
04-02-2009, 06:12 PM
everything has already been pre-determined, the motor will be rebuilt and ported. im not just going to "throw some shit in it" and get it going, thats not how i roll (obviously since my car still doesn't roll under its own power).

guffman
04-02-2009, 07:48 PM
SICK FC i want one
please dont try and suck off chris, he has enough dudes already.

mazdarati
04-05-2009, 11:00 AM
no such thing ;D

guffman
04-05-2009, 11:50 PM
true, true...

mazdarati
05-10-2009, 07:34 PM
steppin up my game a bit:

so as most of you know my car has been down (but not out) for some time. well i finally scraped up some money and threw what i could at a rebuild kit for the 13B. Along with basically just rebuilding the engine, i will also have the engine ported and i will remove the rat's nest of vacuum lines and cap off all of the extra BS that is making my engine bay so cluttered. Also i have thoroughly cleaned out my lower intake manifold including the the 6PI induction system and the actuators that make them work. they had been siezed in there for so long that parts were breaking left and right as i was taking them out. After cleaning all this mess up it has come to be quite obvious that the car had sat for quite some time seeing as how the sunroof was rusted through almost all over. so all in all, this project is coming along pretty well, i will have a list of what else i need for josh to finish up the motor and then back in the car she goes.

i will be accepting ideas as far as painting the rotor housings, i figure i might as well do that before the engine is put back together. some ideas:

Jakins
05-11-2009, 10:18 AM
oooooohh, now i understand how 4 rotors are made :)

Army_Drifter
05-11-2009, 04:42 PM
i like the gold and black, kinda looks like R2D2!

killakingquan
05-11-2009, 04:49 PM
i like the gold and black, kinda looks like R2D2!

wasnt r2d2 blue and white tho

Army_Drifter
05-11-2009, 04:54 PM
well whoever the other one was....oh....C3PO!!! haha your right....shut up!

Clarkbar
05-11-2009, 08:26 PM
Chris... Gold and white!!!! Do work son!!